![]() In forward i should not be able to turn the prop counter clock wise. I have done the work and tried reinstalling the lower leg. I have decided to change the impeller and gearbox oil before starting it up. The inherent simplicity of the Mercury TLDI 75 is so refreshing compared to the complexity of double overhead camshafts and interference four-stroke engines, where should the timing belt break, it’s goodbye boating pleasure.Īs of July 2012 the Mercury TLDI 75 had a price of $13,459 RRP, with a spare Power Tech prop costing $900.I have purchased a boat that has not been used for a few years. It’s true that the Mercury 75 hp two-stroke, like its E-TEC and OptiMax competition, doesn’t have the smoothness of Honda’s four-cylinder BF75, but it’s substantially lighter and power delivery is quicker - important in situations like bar crossings.Īs for reliability, it’s no secret in the Aussie boating industry that the OCP (also used in OptiMax engines) is the most reliable of all DFI systems. The TLDI system also has a diagnostic system that doesn’t require a laptop to analyse faults, resulting in less servicing technician time and potentially lower servicing costs than carbie two-stroke engines in this power range. Sure, 3 Stars translates to fewer exhaust emissions, but the real benefit for Aussie boaters is the lower fuel consumption. Across the entire rpm range the vibration levels were slightly lower and my gut feeling was the engine was matched perfectly to the hull, which, after all, is rated to 75hp.įorget OEDA ratings for this engine. As with any fuel-injected petrol engine, loading it up simply uses more fuel because the EFI is trying hard to compensate.Īs with the Mercury 90, using premium unleaded petrol and OptiMax oil, the Mercury TLDI 75 outboard motor started instantly hot or cold with no oil smoke appearing at any time, just a slight oil smell when backing upwind. The WOT fuel consumption was way down on Tohatsu’s stated maximum of 26lt/h because the engine could rev so freely. Two inches can make a world of difference (wiser words were never spoken - Ed.) The engine had less loading across its entire rpm range and, because it revved right out to 5800rpm instead of 5500rpm, it returned incredible fuel efficiency for a 75hp outboard motor. However, Lakeside’s Dave Denny, one incredibly thorough guy, fitted a 15in-pitch Power Tech stainless steel prop to allow the Mercury TLDI 75 outboard to rev right out, whereas the Mercury 90 engine was fitted with a 17in Power Tech. Mounted on a Makocraft 4.85 MF Frenzy side-console tinnie, the review Mercury TLDI 75 outboard motor was pushing exactly the same 900kg total displacement as the 90 on this hull, including two adults and test gear. Servicing intervals are every 50 hours or annually after the first service at 10 hours, and the recreational-usage warranty is three years. The gear reduction is a usefully-low 2.33:1, enabling coarse-pitch and thrust-efficient props to be swung. The under-flywheel alternator produces a maximum of 40amp, and the dry weight is 150kg. Lakeside Marine, the national Tohatsu distributor, recommends using Quicksilver OptiMax DFI oil in all its TLDI models. ![]() ![]() The variable-ratio oil injection has a large 4lt powerhead-mounted tank, and oil is delivered by an electric pump. ![]() This translates to incredibly low fuel consumption when trolling, yet plenty of torque and power to rapidly plane a hull. The Mercury 75 hp TLDI has the same orbital combustion process (OCP) developed by the Orbital Engine Corporation of Western Australia and utilises a mix of stratified and homogenous combustion. So, on paper, the Mercury 75 hp is way down on output. The three-cylinder powerhead displaces 1267cc and produces 120Nm of torque at 4000rpm, whereas the Mercury TLDI 90’s maximum torque is 135Nm at 4250rpm. The OEDA 3 Star Mercury 75 develops 74.0hp at 5500rpm with a wide open throttle (WOT) rpm range of 5150 to 5850.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |